CCNA Final

CCNA 2 Final Exam Answers 2012

1. Which two statements are true for link-state routing protocols? (Choose two.)

Routers that run a link-state protocol can establish a complete topology of the network.

Routers in a multipoint network that run a link-state protocol can exchange routing tables.

Routers use only hop count for routing decisions.

The shortest path first algorithm is used.

Split horizon is used to avoid routing loops.

 

2.

ERouting Final Exam CCNA 2 Version 2012

Refer to the exhibit. RouterA and RouterB cannot successfully exchange EIGRP routes. What is the problem?

The hello intervals do not match.

The autonomous system numbers do not match.

The no auto-summary command is missing from both routers.

The ip bandwidth-percent command is missing from RouterB.

CCNA 3 Final Exam Answers 2012

1. A wireless client is attempting to establish a connection with a wireless access point. What process does the client use to discover the access points which are available to it?

probing

beaconing

association

authentication

 

2.

LAN Switching and Wireless

Refer to the exhibit. Each switch is shown with its MAC address. Which switch will be elected as the spanning-tree root bridge if the switches are configured with their default priority values?

switch A

switch B

switch C

switch D

switch E

switch F

CCNA 4 Final Exam

1. Which functions are provided by LCP and NCP as part of the PPP layered architecture?

LCP sets up the PPP connection and its parameters. NCP terminates the PPP connection.

LCP sets up the PPP connection and its parameters. NCP handles higher layer protocol configurations.

LCP includes the link-establishment phase. NCP includes link-maintenance and link-termination phases.

LCP negotiates options for multiple network layer protocols. NCP agrees automatically on encapsulation formats.

 

2.

CCNA Final 2011

Refer to the exhibit. EIGRP has been configured on routers R1 and R2. Connectivity across the Frame Relay switch between routers R1 and R2 is successfully verified using the ping command. However, no EIGRP routes are appearing in the routing table. What could be a cause for this failure?

The Frame Relay switch has failed.

The frame-relay map statement is incorrect.

The S0/0/0 interface of router R1 is administratively down.

The S0/0/0 interface of router R2 has an incorrect IP address.

CCNA 4 Final Exam Answers 2011

CCNA 4 Final Exam Answers 2011

1. Which Frame Relay flow control mechanism is used to signal routers that they should reduce the flow rate of frames?

DE

BE

CIR

FECN

CBIR

 

2. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administrator receives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of the problem?

When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.

Incorrect IPv4 addresses are entered on the router interfaces.

RIPng is incompatible with dual-stack technology.

IPv4 is incompatible with RIPng.

CCNA 1 Final Exam Answers 2011

CCNA 1 Final Exam Answers 2011

1. Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.)
Router(config)# line vty 0 3
Router(config-line)# password c13c0
Router(config-line)# login

The entries specify three Telnet lines for remote access.

The entries specify four Telnet lines for remote access.

The entries set the console and Telnet password to "c13c0".

Telnet access will be denied because the Telnet configuration is incomplete.

Access will be permitted for Telnet using "c13c0" as the password.

 

2. Which two actions could be taken by a router if a specific match is not made to a route in the routing table? (Choose two.)

The packet will be discarded.

The packet will be sent back to the source.

The packet will be flooded out all interfaces.

Neighboring routers are polled to find the best path.

The packet will be forwarded to a default route if one is present.

CCNA 4 Final Exam V4.0 Answers

CCNA 4 Final Exam V4.0 Answers

1. What functionality do access control lists provide in the implementation of dynamic NAT on a Cisco router?

define which addresses can be translated

define which addresses are assigned to a NAT pool

define which addresses are allowed out the router

define which addresses can be accessed from the inside network

 

2. Which three guidelines would help contribute to creating a strong password policy? (Choose three.)

Once a good password is created, do not change it.

Deliberately misspell words when creating passwords.

Create passwords that are at least 8 characters in length.

Use combinations of upper case, lower case, and special characters.

Write passwords in locations that can be easily retrieved to avoid being locked out.

Use long words found in the dictionary to make passwords that are easy to remember.

CCNA 3 Final Exam V4.0 Answers

1. Which security protocol or measure would provide the greatest protection for a wireless LAN?

WPA2

cloaking SSIDs

shared WEP key

MAC address filtering

 

2.

CCNA 1 Final Exam V4.0 Answers
Refer to the exhibit. All trunk links are operational and all VLANs are allowed on all trunk links. An ARP request is sent by computer 5. Which device or devices will receive this message?

only computer 4

computer 3 and RTR-A

computer 4 and RTR-A

computer 1, computer 2, computer 4, and RTR-A

computer 1, computer 2, computer 3, computer 4, and RTR-A

all of the computers and the router

 

CCNA 2 Final Exam V4.0 Answers

1.

CCNA 2

Refer to the exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on the Paris router? (Choose three.)

Paris(config)# router eigrp 100

Paris(config)# router eigrp

Paris(config-router)# network 192.168.6.0

Paris(config-router)# network 192.168.7.0

Paris(config-router)# network 192.168.8.0

Paris(config-router)# network 192.168.9.0

 

2. In a lab test environment, a router has learned about network 172.16.1.0 through four different dynamic routing processes. Which route will be used to reach this network?

D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0

O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0

R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0

I 172.16.1.0/24 [100/1192] via 192.168.200.1, 00:00:09, Serial0/0/0

CCNA 1 Final Exam V4.0 Answers

1.

CCNA 1 Final Exam V4.0 Answers (1)

Refer to the exhibit. What is the correct destination socket number for a web page request from Host A to the web server?

00-08-a3-b6-ce-46

198.133.219.25:80

http://www.CCNAAnswers.com

C 198.133.219.0/24 is directly connected, FastEthernet0/0

 

2. Which prompt represents the appropriate mode used for the copy running-config startup-config command ?

Switch-6J>

Switch-6J#

Switch-6J(config)#

Switch-6J(config-if)#

Switch-6J(config-line)#