Final Exam

CCNA 2 Final Exam Answers 2012

1. Which two statements are true for link-state routing protocols? (Choose two.)

Routers that run a link-state protocol can establish a complete topology of the network.

Routers in a multipoint network that run a link-state protocol can exchange routing tables.

Routers use only hop count for routing decisions.

The shortest path first algorithm is used.

Split horizon is used to avoid routing loops.



ERouting Final Exam CCNA 2 Version 2012

Refer to the exhibit. RouterA and RouterB cannot successfully exchange EIGRP routes. What is the problem?

The hello intervals do not match.

The autonomous system numbers do not match.

The no auto-summary command is missing from both routers.

The ip bandwidth-percent command is missing from RouterB.

CCNA 3 Final Exam Answers 2012

1. A wireless client is attempting to establish a connection with a wireless access point. What process does the client use to discover the access points which are available to it?







LAN Switching and Wireless

Refer to the exhibit. Each switch is shown with its MAC address. Which switch will be elected as the spanning-tree root bridge if the switches are configured with their default priority values?

switch A

switch B

switch C

switch D

switch E

switch F

CCNA 4 Final Exam

1. Which functions are provided by LCP and NCP as part of the PPP layered architecture?

LCP sets up the PPP connection and its parameters. NCP terminates the PPP connection.

LCP sets up the PPP connection and its parameters. NCP handles higher layer protocol configurations.

LCP includes the link-establishment phase. NCP includes link-maintenance and link-termination phases.

LCP negotiates options for multiple network layer protocols. NCP agrees automatically on encapsulation formats.



CCNA Final 2011

Refer to the exhibit. EIGRP has been configured on routers R1 and R2. Connectivity across the Frame Relay switch between routers R1 and R2 is successfully verified using the ping command. However, no EIGRP routes are appearing in the routing table. What could be a cause for this failure?

The Frame Relay switch has failed.

The frame-relay map statement is incorrect.

The S0/0/0 interface of router R1 is administratively down.

The S0/0/0 interface of router R2 has an incorrect IP address.

CCNA 4 Final Exam Answers 2011

CCNA 4 Final Exam Answers 2011

1. Which Frame Relay flow control mechanism is used to signal routers that they should reduce the flow rate of frames?







2. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administrator receives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of the problem?

When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.

Incorrect IPv4 addresses are entered on the router interfaces.

RIPng is incompatible with dual-stack technology.

IPv4 is incompatible with RIPng.

CCNA 1 Final Exam Answers 2011

CCNA 1 Final Exam Answers 2011

1. Due to a security violation, the router passwords must be changed. What information can be learned from the following configuration entries? (Choose two.)
Router(config)# line vty 0 3
Router(config-line)# password c13c0
Router(config-line)# login

The entries specify three Telnet lines for remote access.

The entries specify four Telnet lines for remote access.

The entries set the console and Telnet password to "c13c0".

Telnet access will be denied because the Telnet configuration is incomplete.

Access will be permitted for Telnet using "c13c0" as the password.


2. Which two actions could be taken by a router if a specific match is not made to a route in the routing table? (Choose two.)

The packet will be discarded.

The packet will be sent back to the source.

The packet will be flooded out all interfaces.

Neighboring routers are polled to find the best path.

The packet will be forwarded to a default route if one is present.