CCNA 1 Module 8 V3.1 Answers

1. A network administrator has a multi-floor LAN to monitor and maintain. Through careful monitoring, the administrator has noticed a large amount of broadcast traffic slowing the network. Which device would you use to best solve this problem?

bridge

hub

router

transceiver

 

2. What is the function of a Layer 2 switch?

forwards data based on logical addressing

duplicates the electrical signal of each frame to every port

learns the port assigned to a host by examining the destination MAC address

determines which interface is used to forward a frame based on the destination MAC address

 

3.

Refer to the exhibit. The switch and the hub have default configurations, and the switch has built its CAM table. Which of the hosts will receive the data when workstation A sends a unicast packet to workstation C?

workstation C

workstations B and C

workstations B, C, and the E0 interface of the router

workstations B, C, D, E, F, and the E0 interface of the router

 

4.

Refer to the exhibit. Forty-eight workstations are connected to a hub. The users are able to connect to the network, but access is very slow. An entry-level technician replaces the 10 Mbps hub with 100 Mbps hub but the problem still exists. What is the most economical way to correct the problem?

Replace the hub with a switch.

Replace the hub with a router.

Replace the hub with a 1 Gbps hub.

Replace the hub with a 10 Mbps fiber hub.

 

5.

Exhibited is a portion of ABC Company internetwork. Which of the connections can be full duplex?

segments 1 and 2

segment 2

segments 3 and 4

segments 2, 3, and 4

segments 1, 2, 3, and 4

 

6. What will a bridge do if it receives a frame with a MAC address that is not within the table?

discard frame

ignore frame

send frame to appropriate port

send frame to all ports except source port

 

7. What is used to prevent Layer 2 switching loops?

bridging

segmentation

Address Resolution Protocol

Spanning-Tree Protocol

 

8. An administrator would like to connect ten workstations on a 192.168.0.0/24 network. The device selected by the administrator must allow connectivity between hosts without sharing bandwidth. Which device would be appropriate?

hub

router

switch

repeater

 

9. Which devices will create multiple collision domains in an Ethernet network? (Choose two.)

NIC

hub

switch

router

repeater

 

10. Two newly hired technicians are discussing the implementation of a new LAN. One technician proposes installing a hub. The other technician advises installing a switch. Which statements are true about the differences between a hub and a switch? (Choose two.)

A hub operates at Layer 2 of the OSI model.

A hub reduces the number of collisions on a LAN.

A hub works at a higher OSI model layer than a switch.

A switch provides more throughput to hosts on a LAN.

A switch provides a collision-free environment on a LAN.

The number of collisions on a LAN are the same whether a hub or a switch is used.

 

11. A PC receives a frame. Which situation will cause the NIC on the receiving host to pass the frame contents up the OSI layers to be processed by the PC?

The frame is a runt frame.

The destination MAC address of the frame is FFFF.FFFF.FFFF.

The transmitting host generated a jam signal during the frame transmission.

The recalculated checksum for the frame does not match the FCS on the frame.

 

12. Which networking device reduces the size of both collision domains and broadcast domains?

hub

Layer 2 switch

router

bridge

repeater

 

13. Which devices are primarily used to extend cable segments within a collision domain by regenerating the data signals? (Choose two.)

switch

repeater

router

bridge

hub

 

14. Which networking devices use the MAC address to make forwarding decisions? (Choose two.)

NIC

bridge

hub

switch

repeater

 

15.

Refer to the exhibit. How many broadcast domains exist in classroom 240?

1

2

5

12

13

15