CCNA 2 Chapter 2 V4.0 Answers

CCNA 2 Chapter 2 V4.0 Answers

1. A static route that points to the next hop IP will have what administrative distance and metric in the routing table?

administrative distance of 0 and metric of 0

administrative distance of 0 and metric of 1

administrative distance of 1 and metric of 0

administrative distance of 1 and metric of 1

 

2. What address can be used to summarize networks 172.16.1.0/24, 172.16.2.0/24, 172.16.3.0/24, and 172.16.4.0/24?

172.16.0.0/21

172.16.1.0/22

172.16.0.0 255.255.255.248

172.16.0.0 255.255.252.0

CCNA 2 Chapter 1 V4.0 Answers

1. If a router cannot find a valid configuration file during the startup sequence, what will occur?

The startup sequence will reset.

The router will prompt the user for a response to enter setup mode.

The startup sequence will halt until a valid configuration file is acquired.

The router will generate a default configuration file based on the last valid configuration.

The router will monitor local traffic to determine routing protocol configuration requirements.

 

2.

CCNA 2 Chapter 1 V4.0 Answers (1)

Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?

The destination networks do not exist.

The IP addresses on the router interfaces must be configured as network addresses and not host addresses.

The interfaces must be enabled with the no shutdown command.

Each interface must be configured with the clock rate command.

CCNA 1 Final Exam V4.0 Answers

1.

CCNA 1 Final Exam V4.0 Answers (1)

Refer to the exhibit. What is the correct destination socket number for a web page request from Host A to the web server?

00-08-a3-b6-ce-46

198.133.219.25:80

http://www.CCNAAnswers.com

C 198.133.219.0/24 is directly connected, FastEthernet0/0

 

2. Which prompt represents the appropriate mode used for the copy running-config startup-config command ?

Switch-6J>

Switch-6J#

Switch-6J(config)#

Switch-6J(config-if)#

Switch-6J(config-line)#

CCNA 1 Chapter 11 V4.0 Answers

1.
CCNA 1 Chapter 11 V4.0 Answers (1)
Refer to the exhibit. What command will place the router into the correct mode to configure an appropriate interface to connect to a LAN?

UBAMA# configure terminal

UBAMA(config)# line vty 0 4

UBAMA(config)# line console 0

UBAMA(config)# interface Serial 0/0/0

UBAMA(config)# interface FastEthernet 0/1

 

2. In a Cisco router, when do changes made to the running-configuration take effect?

after a system restart

**as the commands are entered

when logging off the system

when the configuration is saved to the startup-configuration

CCNA 1 Chapter 10 V4.0 Answers

1.

CCNA 1 Chapter 10 V4.0 Answers (1)

Refer to the exhibit. A student working in the lab selects a cable that is wired as shown. Which connection types can successfully be made with this cable? (Choose two.)

connecting a PC to a router's console port

connecting two routers together via their fast ethernet ports

connecting two switches together at gigabit speeds

connecting a PC to a switch at Gigabit Ethernet speeds

connecting two devices with the same interface type at Fast Ethernet speeds

 

2. Which three statements are true about the role of routers in the network? (Choose three.)

They propagate broadcasts.

They enlarge collision domains.

They segment broadcast domains.

They interconnect different network technologies.

Each router interface requires a separate network or subnet.

They maintain a common frame format between LAN and WAN interfaces.

CCNA 1 Chapter 9 V4.0 Answers

CCNA 1 Chapter 9 V4.0 Answers

1. In the graphic, Host A has reached 50% completion in sending a 1 KB Ethernet frame to Host D when Host B wishes to transmit its own frame to Host C. What must Host B do?

Host B can transmit immediately since it is connected on its own cable segment.

Host B must wait to receive a CSMA transmission from the hub, to signal its turn.

Host B must send a request signal to Host A by transmitting an interframe gap.

Host B must wait until it is certain that Host A has completed sending its frame.

 

2. Ethernet operates at which layers of the OSI model? (Choose two.)

Network layer

Transport layer

Physical layer

Application layer

Session layer

Data-link layer

CCNA 1 Chapter 7 V4.0 Answers

CCNA 1 Chapter 7 V4.0 Answers

1. Which options are properties of contention-based media access for a shared media? (Choose three.)

non-deterministic

less overhead

one station transmits at a time

collisions exist

devices must wait their turn

token passing

 

2. What is a primary purpose of encapsulating packets into frames?

provide routes across the internetwork

format the data for presentation to the user

facilitate the entry and exit of data on media

identify the services to which transported data is associated

CCNA 1 Chapter 6 V4.0 Answers

1. How many bits make up an IPv4 address?

128

64

48

32 **

 

2.
CCNA 1 Chapter 6 (1)
Refer to the exhibit. A network administrator has to develop an IP addressing scheme that uses the 192.168.1.0 /24 address space. The network that contains the serial link has already been addressed out of a separate range. Each network will be allocated the same number of host addresses. Which network mask will be appropriate to address the remaining networks?

255.255.255.248

255.255.255.224

255.255.255.192

255.255.255.240

255.255.255.128

255.255.255.252

CCNA 1 Chapter 5 V4.0 Answers

CCNA 1 Chapter 5 V4.0 Answers

1. In an IPv4 environment, what information is used by the router to forward data packets from one interface of a router to another?

destination network address

source network address

source MAC address

well known port destination address

 

2. What information is added during encapsulation at OSI Layer 3?

source and destination MAC

source and destination application protocol

source and destination port number

source and destination IP address